XM AUTH TOOL / BD AUTH

XM AUTH TOOL / Xiaomi BD AUTH — Authorization Services

8 min read

What is XM AUTH TOOL / Xiaomi BD AUTH?

XM AUTH TOOL (also known as Xiaomi BD AUTH) is a specialized tool focused on Xiaomi authentication bypass — specifically the MTK DA (Download Agent) authentication and Xiaomi server-side authorization that blocks low-level access on newer Xiaomi devices.

The Xiaomi Auth Problem

Modern Xiaomi devices with MediaTek chipsets implement multiple layers of authentication that prevent unauthorized BROM access:

MTK Secure Boot: The SoC verifies the signature of the Download Agent (DA) file before allowing BROM operations. Only Xiaomi-signed DAs are accepted
SLA (Serial Link Authentication): Even if BROM handshake succeeds, the device demands SLA keys signed by the OEM (Xiaomi) before allowing read/write
DAA (Download Agent Authentication): Newer MT6853/MT6877/MT6893/MT6983 SoCs require DA files authenticated against Xiaomi's server before any operation

Without auth bypass, tools cannot perform IMEI repair, Mi Account removal, or flash operations via BROM on these secured devices.

What XM AUTH TOOL Does

Function	Detail
Auth Bypass	Bypasses MTK SLA/DAA authentication on Xiaomi devices, allowing other tools to perform BROM operations
DA File Generation	Generates or patches Download Agent files compatible with specific Xiaomi MTK models
BROM Access	Enables BROM mode access on auth-locked devices: once authenticated, allows NVRAM read/write, flash, format
Mi Account Remove	After auth bypass, removes Mi Account partition data
FRP Bypass	Clears FRP partition after auth

Supported SoCs Requiring Auth

MT6765/MT6768/MT6769 (Helio G35/G85/G80) — Redmi 9/10/12 base models
MT6833/MT6853 (Dimensity 700/720) — Redmi Note 11/12 5G, POCO M3/M4
MT6877/MT6893 (Dimensity 900/1200) — Redmi Note 11 Pro+, POCO X3 GT
MT6895/MT6983/MT6985 (Dimensity 8100-9200) — Xiaomi 12T, Redmi K50

XM AUTH is typically used alongside another repair tool (like Xiaomi Fix Pro, XFT, or a general MTK tool) — XM AUTH handles the authentication, then the other tool performs the actual repair operation.

How to Use XM AUTH TOOL: Step-by-Step

Purchase XM AUTH credits from Code-GSM
Download and install XM AUTH Tool
Log in
Put the MTK Xiaomi device in BROM mode: Power off completely → hold Vol Up → connect USB cable
Click "Auth Bypass" in XM AUTH — the tool handles SLA/DAA authentication
Wait for "Auth Success" in the log
Now switch to your repair tool (Xiaomi Fix Pro, XFT, Pandora, etc.) WITHOUT disconnecting USB — the auth is active
Perform your operation (IMEI, Mi Account, Flash) in the repair tool

Important: Auth Workflow

XM AUTH does NOT perform repairs itself — it only unlocks the auth gate so other tools can work
Keep the phone connected and in BROM mode throughout — disconnecting requires re-auth
Run XM AUTH first, get "Auth Success", then open your repair tool
Not all MTK SoCs require auth — older MT6580/MT6735 don't need it. Newer MT6765+ do

Browse XM AUTH at Code-GSM

Xiaomi / Redmi / POCO Connection Modes

Mode	How to Enter	Chipset	Used For
Fastboot Mode	Power off → hold Vol Down + Power together until Fastboot/Mi Bunny screen appears. Shows "FASTBOOT" or the Mi Bunny dead animation. Connect USB	All (MTK + QC)	Flash ROM, bootloader unlock, FRP erase (unlocked BL), Mi Account removal (some methods), reboot to other modes
MTK BROM Mode	Power off completely → hold Vol Up → plug in USB. If Vol Up doesn't work, try Vol Down. Phone shows as "MediaTek USB Port" (COM) in Device Manager. No screen display in BROM mode	MediaTek only	NVRAM read/write (IMEI repair), format userdata+frp, Mi Account partition erase, flash scatter file, DA auth bypass for locked BROM
Qualcomm EDL (9008)	Options: (1) `adb reboot edl` from ADB; (2) `fastboot oem edl` from Fastboot; (3) Hardware test point (short two test pads on PCB while connecting USB). Shows as "QHSUSB_DLOAD" on COM port in Device Manager	Qualcomm only	Firehose flash (full ROM), NV backup/restore (IMEI), Mi Account partition erase, dead-boot recovery
Recovery Mode	Power off → hold Vol Up + Power until Mi Recovery screen appears	All	Factory reset, ADB sideload, clear cache. Note: Mi Recovery will not allow sideload without unlocked bootloader
ADB Mode	Settings → Additional Settings → Developer Options → USB Debugging. Connect USB → Allow on phone	All (normal boot)	Remote commands, FRP bypass via ADB sideload, trigger reboot to Fastboot/EDL

Anti-Rollback (ARB) Protection — Critical for Xiaomi

Xiaomi devices implement an Anti-Rollback (ARB) counter burned into the chipset's eFuse storage. Each firmware version has an ARB index. Flashing firmware with a lower ARB index than the current burned index will permanently brick the device — this cannot be repaired by any tool.

Always verify that the target firmware's ARB index is equal to or higher than the current device ARB before flashing
Xiaomi Flasher Pro and most modern Xiaomi tools check ARB automatically and warn before proceeding
A device bricked by ARB violation cannot be recovered — it is a hardware-level permanent lock

Troubleshooting Xiaomi / Redmi / POCO Operations

Problem	Likely Cause	Solution
Mi Account lock persists after bypass	Mi Account partition was not fully erased, or MIUI/HyperOS re-applies the lock from a backup on first boot	(1) Do not connect to WiFi after the operation until you have fully set up the device; (2) Perform a full factory reset including userdata AND the mi_account partition; (3) For HyperOS: some methods require EDL firehose with a specific programmer that supports the HyperOS partition layout. Update the tool to latest version
MTK Xiaomi not detected in BROM mode	MTK VCOM driver not installed, phone has DA authentication (newer MTK SoCs), or Vol key held too late	Install MTK VCOM drivers. For newer MTK SoCs (MT6833/MT6853/MT6877+) with DA auth: the tool requires a bypass DA file. Check if the tool version supports your specific SoC. Hold Vol key BEFORE connecting USB, not after
Qualcomm Xiaomi not entering EDL (9008)	Fastboot restrictions, ADB not authorized, or EDL command blocked by security	(1) Try `adb reboot edl` first; (2) Try `fastboot oem edl`; (3) Use hardware test point — short specific pads on the PCB while connecting USB. Test point locations are model-specific (search "[model] edl test point"). Phone in EDL shows "QHSUSB_DLOAD" in Device Manager
Flash fails with "ARB Update" or "Anti-Rollback" warning	Target firmware has lower ARB index than device	STOP — do NOT proceed. Flashing will permanently brick the device. Find firmware with an equal or higher ARB index. Use the current or newer firmware only
Bootloader unlock fails / "BL unlock not allowed"	Unofficial unlock: needs Mi account with 72-hour unlock waiting period. System app hasn't marked device eligible	Log into Mi account, apply for unlock at unlock.update.miui.com, wait 72h or 168h (7 days for newer models). Use MiFlash Unlock official tool. Some HyperOS devices require additional waiting
Phone boots to MIUI/HyperOS logo loop after flash	Fastboot ROM flashed on locked bootloader, missing partitions, or incomplete flash	Use EDL or BROM mode to flash the FULL ROM (not just Fastboot-only partitions). Ensure all partitions (boot, system, vendor, userdata) were included. For BROM: use scatter file with all partitions selected
IMEI shows baseband unknown / null after NVRAM repair	NVRAM write incomplete — both IMEI1 and IMEI2 must be written, not just IMEI1	Retry: write IMEI1 AND IMEI2 in BROM mode (MTK) or NV items 550 AND 551 in Diag mode (QC). Flash the modem/baseband partition if IMEI still shows null after write attempt
FRP removed but setup wizard still shows Google account screen	Userdata FRP flag was cleared but the dedicated frp partition was not erased	Erase the frp partition specifically (not just factory reset). In Fastboot: `fastboot erase frp`. In BROM: select format frp partition. Disconnect WiFi before testing the result

Frequently Asked Questions — Xiaomi / Redmi / POCO

Q: What is the difference between Mi Account removal and FRP bypass?
A: Mi Account is Xiaomi's own cloud-based device lock — it activates after factory reset and requires the original Xiaomi/Mi credentials. Google FRP is Android's Google account lock — also activates after factory reset but requires a Google account. Xiaomi devices can have BOTH locks simultaneously. Both must be removed separately.

Q: My Xiaomi is MTK or Qualcomm — how do I find out?
A: Settings → About Phone → Processor (or CPU). MediaTek shows "Helio" or "Dimensity." Qualcomm shows "Snapdragon." Generally: Redmi Note (base), Redmi A/C series, POCO M/C = MTK. Xiaomi Mi/POCO F/X series, Redmi Note Pro/K series = Qualcomm. The chipset determines which mode (BROM vs EDL) and which IMEI method to use.

Q: Will bootloader unlock remove all my data?
A: Yes — official Xiaomi bootloader unlock via Mi Unlock Tool performs a full data wipe. This is by design. Back up all data before proceeding. Third-party BROM/EDL bypass methods may or may not wipe data depending on the method.

Q: What is MIUI vs HyperOS? Does it change repair procedures?
A: MIUI is Xiaomi's older Android skin (up to MIUI 14). HyperOS is the replacement introduced in late 2023 for Xiaomi 14 series and newer flagships. HyperOS changed some partition layouts and added stricter security. Some older bypass methods no longer work on HyperOS — always verify tool support for HyperOS before ordering.

Q: Can a device bricked by Anti-Rollback be recovered?
A: No — ARB violation burns a permanent eFuse flag. The device will not boot and cannot be recovered by any software or hardware method. This is why respecting ARB warnings before flashing is critical.

Q: After Mi Account removal, the phone asks for Mi Account again on first boot — why?
A: This usually happens if the phone connected to WiFi during or after the bypass and downloaded account data again. Do not connect to WiFi immediately after Mi Account removal. Set up the device offline first, then connect to WiFi after completing the full initial setup.

Q: How do I check credits and order history?
A: Log in to code-gsm.com. Your credit balance and order history are visible in your account dashboard.

Back to Knowledge Base